05% Tween-20) and the non-binding buy ZD1839 sites were blocked with 2% bovine serum albumin (BSA) at 37 °C for 2 h. After washing (×3), 100 μl of diluted (neat, 1:10, 1:100) cell supernatant was added and incubated for 1 h at room temperature (RT). The plates were again washed (×3) with PBST and 100 μl of HRPO (10 μg/ml) was added and incubated for 30 min at RT. The plates were washed (×6) to remove excess unbound HRPO and finally, 100 μl of TMB substrate was added and color development was read at 650 nm using a microplate
reader. The control was RPMI media only. The clones with maximum bsmAb secretion capacity were identified and re-cloned by the standard limiting dilution method. Briefly, the cells were placed in a tissue culture plate at a concentration of 1 cell/well. They were then cultured as before, and positive clones were screened using bridge ELISA. The Olaparib mw above cloning and screening steps were repeated until a stable clone was obtained. All incubations were done at 37 °C. Washing (4–5×) was done with PBST after each step. The assay was performed with dengue anti-NS1 mAb (P148.L2 or P148.L1) as capture antibody and the biotinylated P148.L2 mAb as detection antibody. The anti-NS1 mAb P148.L2 was biotinylated with NHS-LC-Biotin (Sigma, USA) as per manufacturers’ instruction. A microtiter plate (NUNC,
Denmark) was coated with 100 μl of purified NS1 mAb P148.L2 in 0.05 M carbonate buffer at 4 °C overnight. Nonspecific binding sites were blocked with 200 μl of 2% BSA for 2 h. Different concentrations of the dengue NS1 antigen ranging from 20 ng/ml to 0 (20, 10, 5…0) were used, then the plate was incubated at 37 °C for 1 h. Thorough washing (3–5×) was completed and 100 μl of the biotin labeled P148.L2
mAb (2 μg/ml) was added to each well and incubated at 37 °C for 1 h. After incubation, the plate was washed (3–5×) and streptavidin-HRPO (Sigma, USA) was added and incubated at 37 °C for 30 min. Subsequently, TMB substrate (Kirkegaard & Perry Laboratory, USA) was added (Blake et al 2001). OD650 was measured after 15 min using an ELISA Vmax kinetic microplate reader Casein kinase 1 (Molecular Devices Corp., USA). Except as otherwise indicated, all incubation steps were performed at 37 °C for 1 h. Washing five times was conducted by PBS-T between each step. Plates were coated with 100 μl of purified anti-NS1 mAb (P148.9L2 or P148.L1) in 50 mM carbonate buffer (pH 9.6). The remaining sites on the well surface were blocked with 200 μl of blocking buffer (3% (w/v) BSA in PBS-T) at 37 °C for 1 h. A volume of 100 μl of dengue NS1 (serial dilution in 1% (w/v) BSA in PBS-T) was added to the wells, which was then followed by an additional 100 μl of bsmAb-HRPO complex (P156). Plates were washed (3–5×) and TMB substrate was added for colour development and subsequently read at 650 nm after 5 min incubation using an ELISA plate reader.
Related posts:
- Right after four washes in TBS containing Tween , the membranes
- For phage ELISA, wells of Costar EIA RIA high binding plates were
- Andarine GTX-007 was measured by using the method described above for TFV
- Cytotoxicity MTT assay HT29, MCF7, and HepG2 cells lines w ere pl
- EGFR kinase was purchased from Carna Biosciences Staurosporine w