100 to 200 nm and 20 to 30 nm, respectively. Figure 2e shows an enlarged TEM image, revealing the porous character of the nanorods. Figure 2f depicts an HRTEM image of one single nanorod, revealing that the obtained nanorod consists of small nanoparticle subunits. As shown in the inset of Figure 2f, the selected-area electron diffraction (SAED) pattern with polycrystalline-like diffraction also indicates that the nanorod is an ordered assembly of small nanocrystal subunits without crystallographic orientation, well consistent with the HRTEM results. Figure 2 Morphology of the BIBW2992 cost cubic MnO nanorods obtained at 200°C for
24 h. (a) Low-magnification and (b) high-magnification SEM images, (c, d, and e) TEM, and (f) HRTEM images. The inset in (e) is an enlarged TEM image,
and the inset in (f) shows the SAED pattern of one single MnO nanorods. ACY-1215 nmr The chemical composition of the as-prepared MnO nanorods was further confirmed by EDS analysis. The spectrum, taken from the center area of the nanorod, shows four strong signals of Mn, C, O, and Cu (Figure 3). The atomic ratio of Mn and O is about 1.02, indicating that the as-prepared nanorods are consist of high-purity MnO rather than other manganese oxides (e.g., Mn2O3, Mn3O4, and MnO2), in good agreement with the XRD results. The Cu and O may have resulted from the Cu gridding and C support membrane in the TEM observation. Figure 3 EDS spectroscopy Mannose-binding protein-associated serine protease of the as-prepared MnO nanorods. The FTIR spectrum was further
performed to substantiate the formation of MnO and the organic residue on the surface of MnO nanorods. As shown in Figure 4, two strong peaks at about 630 and 525 cm−1 arise from the stretching vibration of the Mn-O and Mn-O-Mn bonds [43], indicating the formation of MnO in the present work. In addition, strong absorptions at 3,442 cm−1 and weak absorptions around 2,800 to 3,000 cm−1 reveal the stretching vibrations of O-H and C-H, respectively. The absorption peak at 1,112 cm−1 corresponds to the C-OH stretching and OH bending vibrations, whereas the bands at 1,385, 1,580, and 1,636 cm−1 correspond to C-O (hydroxyl, ester, or ether) stretching and O-H bending vibrations [44, 45]. These results indicate that some organic residues such as hydroxyl and VE822 carboxyl groups are present on the surface of the as-prepared MnO nanorods. Figure 4 FTIR spectroscopy of the as-synthesized MnO nanorods. The presence of the residue functionalities on the surface of the as-synthesize MnO nanorods was further characterized by XPS measurements. As shown in Figure 5, the survey spectrum shows the signals of Mn 2p, O 1s, and C 1s, indicating the presence of carbon element on the surface the nanorods. The presence of the organic groups was further confirmed by the C 1s spectrum. The inset in Figure 5 presents the C 1s core-level spectrum and the peak fitting of the C 1s envelope. Four signals at 284.8, 286.4, 287.
Related posts:
- Figure 6a shows the typical CV curves of the NCONAs electrode wi
- The inset shows the corresponding plots of (αhν)1/2 as a function
- Figure 3D�CG shows that a nuclear CD44/STAT3 signal was required
- As-electrospun AIP/PVP nanofibers calcined at 800°C
had 6 - In Figure 4a, it can be observed that the lengths of the CNTs are